How to Install a Tub ( Guide).
How to Install a Tub ( Guide).
Blog Article
The author is making a number of great observations related to How to Install a Bathtub as a whole in the article just below.
Setting up a tub isn't exactly brain surgery, however it does require strong plumbing, woodworking, and occasionally, tiling abilities. Replacing an old bathtub with a brand-new one is likewise a moderately tough project. If the old bathtub is easily accessible, the task can move speedily; if you need to open a wall surface to eliminate the old tub as well as place the brand-new tub, the task is much harder. In either instance, the task is within a residence handyman's skills, although you will need a helper to leave the old tub and embeded in the new one. Make sure you have actually qualified on your own for the task and fit attempting it. Rather than employing a professional to take control of a halfway-completed project, it is far better to think about employing one before you start. Possibilities are you may require a professional plumber to make tube links.
This short article will certainly assist you install a new bath tub in your shower room if you have already acquired a new tub and also don't require to alter the plan of your previous supply of water pipes.
Your devices as well as material list ought to comprise the following:
Preparing for the Setup
Firstly, the sustaining framework provided with the bath should be fitted (if needed) according to the manufacturer's guidelines. Next, fit the taps or mixer to the bath tub. When fitting the faucet block, it is important to make certain that if the faucet comes with a plastic washing machine, it is fitted in between the bath as well as the faucets. On a plastic bath, it is also practical to fit a sustaining plate under the taps system to stop strain on the tub.
Fit the adaptable tap ports to the bottom of both faucets using 2 nuts as well as olives (occasionally supplied with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet hole, and after that pass the outlet via the hole in the bathroom. Use the nut supplied by the maker to fit the plug-hole. Check out the plug-hole outlet for an inlet on the side for the overflow pipe.
Next off, fit completion of the flexible overflow pipe to the overflow outlet. Afterwards, screw the pipeline to the overflow face which need to be fitted inside the bathroom. Make sure you utilize all of the provided washers.
Link the catch to the bottom of the waste electrical outlet on the bath tub by winding the thread of the waste outlet with silicone mastic or PTFE tape, as well as screw on the trap to the electrical outlet. Attach all-time low of the overflow tube in a comparable manner.The bath should currently prepare to be suited its final position.
Removing Old Touches
If you require to change old faucets with brand-new ones as a part of your setup, after that the first thing you must do is detach the supply of water. After doing so, switch on the taps to drain any water remaining in the system. The process of getting rid of the existing faucets can be fairly troublesome because of the restricted gain access to that is frequently the case.
Make use of a container wrench (crowsfoot spanner) or a tap tool to reverse the nut that links the supply pipes to the faucets. Have a towel prepared for the remaining water that will certainly originate from the pipes. When the supply pipes have been gotten rid of, make use of the exact same tool to loosen the nut that holds the faucets onto the bath/basin. You will certainly need to stop the single faucets from transforming during this procedure. When the taps have actually been eliminated, the holes in the bath/basin will need to be cleaned of any kind of old securing compound.
Prior to carrying on to fit the new taps, compare the pipe links on the old faucets to the brand-new taps. If the old taps are longer than the new faucets, after that a shank adapter is required for the new taps to fit.
Mounting the Bath tub
Utilizing the two wood boards under its feet, place the bathtub in the called for setting. The wooden boards are handy in evenly spreading out the weight of the tub over the area of the boards as opposed to concentrating all the weight onto four tiny points.
The next objective is to guarantee that the bath tub is leveled all round. This can be accomplished by checking the level as well as adjusting the feet on the tub until the level reviews degree.
To install faucets, fit all-time low of the furthest flexible faucet port to the appropriate supply pipeline by making a compression join; then do the very same for the other tap.
Activate the supply of water and examine all joints as well as brand-new pipework for leakages and tighten them if essential. Fill up the bathtub as well as likewise examine the overflow electrical outlet and the regular outlet for leakages.
Lastly, fix the bathroom paneling as described in the supplier's instruction manual. Tiling and also securing around the bathtub must wait until the bath tub has been utilized at least when as this will resolve it into its last position.
Suitable New Taps
If the tails of the brand-new taps are plastic, after that you will certainly need a plastic port to prevent damage to the string. One end of the port fits on the plastic tail of the faucet and the various other end provides a link to the existent supply pipelines.
If you require to fit a monobloc, after that you will call for decreasing couplers, which attaches the 10mm pipe of the monobloc to the common 15mm supply pipe.
Next, place the tap in the installing opening in the bath/basin guaranteeing that the washing machines are in location between the faucet and the sink. Protect the tap in place with the supplier supplied backnut. As soon as the tap is firmly in place, the supply pipelines can be attached to the tails of the taps. The taps can either be attached by using corrugated copper piping or with regular tap ports. The previous type needs to be connected to the faucet ends first, tightening up just by hand. The supply pipes can later be attached to the various other end. Tighten both ends with a spanner after both ends have been attached.
Tiling Around the Bathtub
In the location where the bath satisfies the floor tile, it is necessary to secure the accompanies a silicone rubber caulking. This is essential as the installation can move sufficient to crack an inflexible seal, causing the water to permeate the wall in between the bathroom and also the tiling, resulting in difficulties with dampness and feasible leaks to the ceiling below.
You can pick from a variety of coloured sealants to assimilate your fixtures as well as installations. They are sold in tubes as well as cartridges, and are capable of sealing voids approximately a width of 3mm (1/8 inch). If you have a larger space to load, you can load it with twists of soaked newspaper or soft rope. Bear in mind to constantly load the bathtub with water before sealing, to enable the activity experienced when the tub is in use. The sealant can split rather very early if you do not take into account this motion before securing.
Conversely, ceramic coving or quadrant floor tiles can be made use of to edge the bath or shower tray. Plastic strips of coving, which are easy to use and cut to size, are likewise conveniently readily available on the marketplace. It is advisable to fit the tiles using water-resistant or water resistant adhesive and grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
I ran across that piece of writing on A Step-by-Step Guide to Installing a Bathtub when doing a search on the internet. Are you aware of somebody else who is excited about the topic? Why not promote it. Thanks a lot for going through it.
Visit My Website Report this page